Skip navigation

Machines

PEDDINGHAUS Peddimax 602, Metal Processing, Sheet metal working / shaeres / bending, Section Steel Shear

PEDDINGHAUS

Peddimax 602

Kategorie 1:
Metal Processing
Kategorie 2:
Sheet metal working / shaeres / bending
Kategorie 3:
Section Steel Shear

Furnishing: - Stop / support table at punching station - Support table at the notching station - Flat steel knife, 375 mm long, with four cutting edges, - also for angle steel section 45° - Material support table with stop bar on the flat steel shears - Profile steel knife for cutting angle steel 90° as well as round steel and square steel - Scraper, swivelling - Square notching device with stop table - 2x footswitches and electrical controls - connector for external engagement, - Hydraulic unit, integrated - Three-phase motor, 400 volts, 50 Hz - Various application tools - other accessories such as PEDDINGHAUS length stop

Lagernummer:
1008-9412142
punching pressure:
60,0 t
punching cross-cut in cmm:
31 in 15 mm
square edge steel:
40,0 mm
L-beam:
160 x 80 mm
PEDDINGHAUS PEDDIMASTER 60/80, Metal Processing, Sheet metal working / shaeres / bending, Section Steel Shear

PEDDINGHAUS

PEDDIMASTER 60/80

Kategorie 1:
Metal Processing
Kategorie 2:
Sheet metal working / shaeres / bending
Kategorie 3:
Section Steel Shear

Furnishing: - hydraulic, combined profile steel shears * with release station * with hole punching station .. punching capacity 60kN * Flat steel shears .. shearing capacity 80kN * Angle steel scissors * Square steel scissors * Round bar shears - Support table at the notching station - Stripper at the punching station - free-moving footswitch - Safety devices - User manual (PDF)

Lagernummer:
1008-9412141
pressure:
60,0 / 80,0 t
punching cross-cut in cmm:
27,0 in 17,0 mm
stroke:
10 - 27,5 mm
throat:
410 mm
MUHR & BENDER MIW 400, Metal Processing, Sheet metal working / shaeres / bending, Section Steel Shear
Kategorie 1:
Metal Processing
Kategorie 2:
Sheet metal working / shaeres / bending
Kategorie 3:
Section Steel Shear

** from a maintenance workshop ** very good condition (!!) Furnishing: - hydraulic profile steel shears - Punching station, flat steel shears, angle steel shears, profile steel shears - stepless adjustment of the stroke - very compact design - Support table at the notching and punching station - Quick change device on the punching side - Square notchers - Protective devices at work stations - foot switch

Lagernummer:
1008-9412133
punching pressure:
40,0 t
square edge steel:
28,0 mm
L-beam:
80 x 8,0 mm
round bar steel:
30,0 mm
MUHR & BENDER HIW 750, Metal Processing, Sheet metal working / shaeres / bending, Section Steel Shear
Kategorie 1:
Metal Processing
Kategorie 2:
Sheet metal working / shaeres / bending
Kategorie 3:
Section Steel Shear

Furnishing: - hydraulic profile steel shear - Punching station with support table - Infinitely variable stroke adjustment with inching/setup mode - Triangular notching station with support table - Bar, profile and angle steel shears - Flat steel station with support and guide table / adjustable stop bar - foot switch - Bed. Instructions Special accessories included : - electrical contact length stop

Lagernummer:
1008-9412139
hole punhing press: pressure:
75,0 t
output:
30 in 22 mm
round bar steel:
50,0 mm
square edge steel:
45,0 mm
PEDDINGHAUS PEDDIMASTER 80/110, Metal Processing, Sheet metal working / shaeres / bending, Section Steel Shear

PEDDINGHAUS

PEDDIMASTER 80/110

Kategorie 1:
Metal Processing
Kategorie 2:
Sheet metal working / shaeres / bending
Kategorie 3:
Section Steel Shear

** very good condition (!!) Furnishing: - hydraulic, combined profile steel shears * with release station * with punching station .. punching capacity 800kN * Flat steel shears .. Shear capacity 100kN * Angle steel scissors * Angle steel knife for cutting 90 ° & 45 ° miters * Cutting angle steel + T-steel + I-steel - Support table at the notching station - Scraper at the punching station - Freely movable foot switch - Central lubrication - Safety devices - Operating instructions (PDF)

Lagernummer:
1008-9412137
pressure:
80,0 / 110 t
punching cross-cut in cmm:
27,0 in 20 mm
L-beam:
120 x 13 mm
L-beam:
T 120 x 12 mm
MUHR & BENDER MIW 800, Metal Processing, Sheet metal working / shaeres / bending, Section Steel Shear
Kategorie 1:
Metal Processing
Kategorie 2:
Sheet metal working / shaeres / bending
Kategorie 3:
Section Steel Shear

** from a maintenance workshop ** very good condition, like new (!!) Furnishing: - hydraulic profile steel shear - Stamping station, flat steel shears, angle steel shears, profile steel shears - Stepless adjustment of the stroke - very compact design - Support table at the notching and punching station - Quick change device on the punching side - Square notcher - Protective devices at workstations - free-moving footswitch

Lagernummer:
1008-9412145
punching pressure:
80,0 t
square edge steel:
28,0 mm
L-beam:
110 x 10 mm
round bar steel:
30,0 mm